Join favoritesContact us
Products
Location： Home|Development|Products|Hardware|TCP/IP Door Controller
Products Brand center
BS511 Single Door Network Controller

  • Product overview:

    [Features]

    ◆ Using 32 bit ARM chip set, operate on LINUX OS, speed up to 200MHz
    ◆ Direct connection to computer via TCP/IP, need not go through TCP/IP converter. Transmission speed up to 100Mbps
    ◆ Max 100,000 Card Holders and 100,000 off-line Transaction
    ◆ Using Flash Memory to store data. Data can be stored up till 10 years
    ◆ Recoverable up till 10,000 lines of transaction
    ◆ Firmware Upgrade via TCP/IP or RS-232
    ◆ Smart Door Lock capability
    ◆ Separately configure door access mode by PIN or Time Zone Control
    ◆ Display Name and Staff ID when access is granted
    ◆ CE Certified

  • Detail parameters:

    [Functions] 

    Function

    Description

    Card Open Door

    Connect wiegand reader

    Card + PIN Open Door

    		1. Make use of door access controller
    2. Connect external BS36K keypad reader via wiegand and have it set to free wiegand type
    3. Choose either PIN open door or Card ID open door 
    4. Card + PIN: 4 digits PIN; PIN Only : 8 digits PIN

    PIN Open Door

    Card ID Open Door

    Fingerprint Open Door

    Connect BS fingerprint card reader via wiegand. At the same time the following mode can be implemented: Card + Fingerprint, ID + Fingerprint, Fingerprint + PIN, Card + Fingerprint + PIN, ID + Fingerprint + PIN, Card Only, Card + PIN, PIN Only , Card ID Only etc.

    Connect External 26/32 Wiegand Card Reader

    Yes

    Free Wiegand Setup

    Yes. Can set low battery voltage alarm when use with long range card reader.

    Connect External Keypad Reader

    1. Wiegand keypad reader 
    2. BS Chinese series keypad reader(via wiegand)

    Connect External BS Fingerprint Reader

    Via Wiegand

    Communicate with PC

    		1. RS-232/485 or TCP/IP; Using jumper setting to switch between RS-232 or 485
    2. Use keypad controller to set controller ID
    3. Use keypad controller to set IP Address, Subnet Mask and Gateway

    Door Force Open Alarm

    Yes

    Door Open Too Long Alarm

    Door open delay can be set from 1~255 seconds. Factory default is 5 seconds. Alarm can be disabled.

    Add & Delete Cards During Offline

    Yes

    Dual-cards Verification

    Yes

    Invalid PIN Control

    When using Card + PIN open door and number of PIN retry is over preset limits, the door will be remain locked until locking period is over then it is able to use.

    Same Card Delay Control

    0~255 seconds. Factory default is 0

    Time Zone Control

    32 groups of time zone

    Holiday Control

    Yes

    Report Loss Card

    Yes

    Card Validity Control

    Yes

    Door Auto Release Time Zone

    Yes

    Anti-passback

    Yes

    Card No. Output Byte

    1~4. Default is 4

    Card Display Format

    HEX,DEC,ABA,USER CODE. Default is DEC

    Communication Monitoring

    Yes

    PIN and Time zone Control

    Can be setup to use either PIN control or time zone control

    Tamper Alarm

    Yes

    Reset Door Open Too Long

    Yes

    Terminal Resistance

    Setup using jumper

    Sensor Setup

    Door sensor normal behavior; sensitivity control; whether transaction based on door sensor action.

    User's Name Display

    Display Name and Staff's ID when access is granted



    [Technical Specification]

    Parameters

    Description

    CPU

    ARM9, processor speed up till 200MHz

    Operating System

    Linux

    Control Door Area

    1

    Connect Wiegand Reader

    2

    Door Sensor Signal

    1

    Push Button Signal

    1

    TTL Alarm Input

    1

    Door Relay

    1, 12V/1A

    Alarm Relay

    1, 12V/1A

    TTL Alarm Output

    1, 5V/300mA

    Tamper Switch

    1

    Card Capacity

    100,000

    Card Matching Speed

    <0.5 seconds when controller card storage reaching 10,000 cards

    Transaction Capacity

    100,000

    COM Port

    2, one is using RS-485 to communicate with PC, another one using RS-232 to communicate with printer or other PC.

    TCP/IP

    1, communicate with PC at 10M/100M

    USB

    2, Master USB

    Operation Keypad

    128x64 dots LCD, 4x4 keypad

    Buzzer

    Yes

    Clock Power Battery

    CR2032, 3V

    Supply Voltage

    9-30V/400mA

    Operation Temperature

    -10~50 °C

    Dimension

    161×112×36mm

    Housing

    ABS flame-resistant


    [Choosing A Model]

    Model No.

    Descrption

    BS511

    Network-based Single Door Controller

    BS511-E

    		Network-based Single Door Controller c/w EM Reader.
    Reading Distance >10cm

    BS511-M

    Network-based Single Door Controller c/w Mifare Reader.
    Reading Distance >2.5cm

    BS511-H

    Network-based Single Door Controller c/w HID125 KHZ proximity Reader.
    Reading Distance >4cm


  • Installation mode:

    [Installation Measurement]


Hotline

Address：

Designed by